FAQ
- Run Program
- Turn on FANUC
- Turn the key to Auto mode on Robot
- Move the switch on the Teaching Pendant (TP) to OFF.
- Press Select on the TP and scroll down to the appropriate communication program. (LABVIEW_COM, LV_COM_FRM, etc.)
- Press Enter
- Hit Reset to clear any Faults (Red LED on)
- Hit the green Start button on the Fanuc controller. Light should turn on Green. If it doesn't, then check for errors. Robot will move to it's HOME position.
- Press FCTN -> Abort All to stop program - Green light should turn off
- Arrow up to line 1 of LV_COM_FRM and hit the Green button on the Robot to restart
- View Alarm Screen - if you can't clear an error you will want to do this to see what the real problem is
- Menu -> Alarms -> Alarm Log
- Use Teaching Pendant
- Keyed control knob in T1 position
- Teaching Pendant in ON position
- Press Deadman switch in half way to do anything
- Move robot with Teaching Pendant
- Press Coord until Joint or World Coordinates is selected
- Press Shift and any of the blue motion buttons to move the 6 joints
- Press +%/-% to adjust the speed
- Press the POSN button to view the actual position
- Open and Close Gripper
- Menu -> I/O -> Robot. Press Enter.
- Arrow down to Gripper
- F4 (On) Opens
- F5 (Off) Closes
- Clear Errors on Teaching Pendant
- Push Deadman switch in halfway
- Hold Shift and push Reset on TP
- Backup Instructions
- Menu -> File ->
- F5 -> Util to change device
- F2 -> DIR *.* to see all files
- F5 Util -> Make DIR to create a directory on selected device
- F4 -> Backup -> 8 All of the above to created directory on selected device
- F4 - > Backup -> 0 Next -> 2 Image Backup -> Requires you to manually cycle power – this message is flashed up for about 2 seconds so you might have missed it. On reboot, the image will start automatically.
- You could backup to a USB drive plugged into the Pendant but it is much slower
- Recent Backup
- 12Core-64:HomeESE497_UGradResearchMatlabFanucKinectFanuc_060418 Tech VisitIMAGE and FILES
- Robot I/O
- I/O -> Type -> Robot -> R0[3] Grip Open, R0[4] Grip Closed
- Hide PRIO-230 error message:
- Menu -> Setup -> Error Table -> FCode – 13 (trial and error until PRIO shows up in the FNAME column) and enter ECODE = 230 and 231 Erlog -> Choice -< NODISP/NOERLOG
- Version
- Menu -> 0 Next -> Status -> 2 Version ID
- F Number F132255
- V7.70P/30 – near end of life – no more updates
- Change a register manually
- Data -> R[26]
- Change to PR – position registers
- FTP to transfer files from FANUC robot
- ftp <IP>
- Blank user name and password
- get or mget to download files
- *.ls - text files for programs
- *.tp - compiled programs
A06B-6096-H116 Fanuc Servo Drive Test und Reparatur bei inustrypart.com Ltd - Duration: 1:00. Industrypart GmbH 1,179 views. What Is Ovc Alarm In Fanuc Robot Parts. Hello everyone, I'm new to the forums and I've got a quick question about one of our robots. My problem is the. For the OVC alarm you should be able to cycle power on the controller FCTNOVC alarm probably because your axis limits aren't properly set up so instead of hitting a soft limit which is easy to recover from you hit a hard limit giving the robot the OVC alarm. Cardio navigator software.
6/4/18 FANUC Technician On-Site visit
- Emergency Stop wasn't working when running LABVIEW_COM on teaching pendant
- We added the command
- $MCR_GRP[1].$machinelock=1 ;
- to the program because there was a lot of interference from the Robot servos that we were picking up on the EMG signals from Yuni's experiment. However, this disables the E-Stop. When I called Fanuc to troubleshoot the E-Stop issue, they told me there was no way to disable the E-Stop in software and we needed a technician to replace the E-Stop board. They were wrong! So, we took $machinelock=1 line out of the program and the E-Stop started working again. We'll have to shield our circuits in the future if we need to do something like this again.
- We added the command
Recalibrate
- Keyswitch in T1, Teaching Pendant in On
- Coord Mode until Joint is selected
- Move all 6 joints 30 degrees and then back 30 degrees and then line up the registration marks (photos below)
- Joint 4 doesn't have a mark - just line it up flush - make sure the words are in the up position
- Joint 6 doesn't have a mark - just line up horizontally with the words down.
- If you get 'No Pulse Detected' error on a joint, then you just manually move the joint and then put it back. ????????
- Menu -> Next -> System -> Master/Cal
- If Master/Cal isn't shown in the menu, then you have to enable it:
- Menu -> Next -> System -> Variables -> MasterEnable -> 1. Now Master/Cal will be in the menu.
- Click on Zero Position Master
- Yes (F4)
- If Master/Cal isn't shown in the menu, then you have to enable it:
- You should get warning 'SYST-212 Need to apply DCS parameter'
- Menu -> Next -> System -> DCS
- Scroll down to Mastering parameter: CHGD
- Click Apply (F2)
- Enter Code 1111
- Please Wait ..
- Click OK (F4)
- Should show Mastering parameter: PEND
- Cycle Power
- Test by putting in World Frame and make sure the tip moves in the desired X,Y or Z directions
Joint 1 Simple dns plus.
Pclp. Joint 2
Joint 3
Joint 5
Errors
Fanuc Robot Ovc Alarm
- 'SRV-038 Pulse Mismatch' Error
- If the problem is just 1 axis (G:1 A:5)
- Menu -> Next -> System -> Master/Cal -> RES_PCA (soft key F3)
- Answer Yes. This should clear the alarm
- Menu -> Next -> System -> Master/Cal -> RES_PCA (soft key F3)
- If the problem is just 1 axis (G:1 A:5)
- 'SRVO-062 BZAL Alarm' Error
- Replace 4 C Cell batteries in battery compartment
- Clear Pulse Coders
- Key in T1, Pendant On
- Menu -> Next -> System -> Master/Cal
- If it says Quick in the Menu, go to FCTN/Next/Quick or Full Menus or you won't see System
- F3 (RES_PCA)
- Reset
- Cycle Power
- Repeat (You have to do this 2x)
- Re-Calibrate
- 'MOTN-049 Attempt to move without Calibrated'
- Recalibrate
- If a FANUC error is thrown when the last sent coordinates from the computer were in tool frame 2, the FANUC script must be restarted from line 3.
- The home position PR[1] will be out of bounds in tool frame 2 and the program will not start
- FCTN -> Abort All-> Enter -> Select -> LV_COM_FRM -> Enter -> Down Arrow (x2) (R[27] = 0) -> Reset
Getting Started Guides
What Is Ovc Alarm In Fanuc Robot Parts Store
Retrieved from 'https://classes.engineering.wustl.edu/ese497/index.php?title=Fanuc_How_Tos,_FAQ,_etc.&oldid=2850'